How To Fix A Dirt Devil Vacuum Cleaner: Troubleshoot Guide

Are you facing such ass this problem Vacuum won’t run, Dust escaping from the vacuum, Cleaner won’t pick up or low suction, Headlight not working… in a dust devil vacuum cleaner and you don’t know how to fix a dirt devil vacuum cleaner you’re in the right place

We’ll show the most common troubleshooting that you may face if you have a dirt devil vacuum cleaner and what causes these issues furthermore we’ll show you how to repair a dirt devil vacuum cleaner troubleshooting.

Please follow the instruction below to know:

How to fix a dirt devil vacuum cleaner

How to fix a dirt devil vacuum cleaner?

problem1 :

The vacuum won’t run

possible cause:

1. Power cord not firmly plugged into the outlet.

2. No voltage within the wall plug.

3. Blown fuse or tripped breaker.

4. Thermal Protector activated.

possible solution :

1. Plug unit in firmly.

2. Check fuse or breaker in residence.

3. Replace fuse/reset breaker in residence

4. Unplug and permit the vacuum to cool for 30min. (This will reset the thermal protector).

Problem2:

 The cleaner won’t pick up or have low suction.

possible cause:

1. Dirt container was not put inappropriately.

2. Dirt container full. 3. Brushroll just isn’t on.

4. Dirty/clogged filter.

5. Dirt passage clogged.

6. Cleaning wand not put in appropriately or misaligned

possible solution :

1. Review dirt container removing and replacement

2. Empty dirt container

  • Push down on the carrying handle and pull the dirt container away from the unit.
  • Hold dirt container over the trash can and push down on the bottom launch lever to release the particles.
  • Tap filter firmly against the within of trash can to take away loose dirt.
  • Hold foam filter below running water to scrub.
  • Wring extra water out of the filter.
  • Allow foam filter to dry for at least 24 hours.
  • Place filter under water to clean.
  • Make certain the filter is totally dry earlier than returning to the cleaner.

3. Turn on the brush roll.

4. Remove HEPA filter and clean.

CLEANING YOUR LIFETIME HEPA FILTER :

  • Twist lid to the left.
  • Remove lid.
  • Remove filter assembly from dirt container.
  • Remove the filter by pulling it off of the filter knob.
  • Tap filter firmly against the inside of trash can to take away loose dirt.
  • Hold foam filter under operating water to clean.
  • Wring extra water out of the filter.
  • Allow foam filter to dry for not less than 24 hours.
  • Place filter below water to clean.
  • Make certain the filter is totally dry earlier than returning to the cleaner.

REPLACE FOAM FILTER :

Replace the foam filter by pressing it down on the filter knob till it locks.

Return filter assembly to dirt container.

CLEANING THE EXHAUST FILTER :

  • Loosen the exhaust grille by pressing the locking tab, and removing it.
  • Remove the exhaust filter and shake it clean.
  • The exhaust filter that comes with this unit is a lifetime filter and will be washed. Make certain the filter is totally dry earlier than returning to the cleaner.

NOTE: Scented exhaust filters usually are not washable and must be changed periodically. Some discoloration might seem on the scented filters.

REPLACE EXHAUST FILTER :

  • Replace the cleaned exhaust filter and cover it with an exhaust grille.

5. Remove dirt container and cleaning wand then test the hose inlets for obstructions.

6. Review cleaning wand set up

  • Bring the vacuum cleaner into its vertical locking place.

NOTE: Switch brush rolls off when utilizing the hos.

  • Press the release button to launch the cleaning wand. The cleaning wand with the built-in brush can be utilized for cleaning surfaces.
  • While pressing the hose launch button, pull out the suction hose to release it from the cleaning wand.
  • Straighten the hose and hook the hose clip into the fastening ring to prevent the upright vacuum cleaner from toppling over throughout use.
  • To entry tools, rock Power Brush Tool away from cleaner. To take away tools, grasp the tool and pull up and out of the accessory clip.
  • Attach the accessory of your choice to the suction hose or cleaning wand by firmly pushing it into place.

Problem3:

Dust escaping from cleaner

possible cause:

1. Dirt cup full.

2. Dirt cup not installed accurately

3. Hose not put incorrectly.

4. Rinsable and/ or Filter made with HEPA media not installed fully.

possible solution :

1. Empty dirt cup.

2. Review Dirt Cup removing & replacement.

3. Review Hose set up.

4. Review Filter Removal and Cleaning.

Problem4:

 Vacuum tools won’t pick-up

possible cause:

1. Hose clogged

2. Dirt cup full

3. One or each filter is clogged.

4. Vacuum not selecting up particles.

possible solution :

1. Remove hose and tools; take away the obstruction.

2. Empty dirt cup.

3. Remove each filter and clean.

4. Brushroll could be turned off or the belt might be damaged.

Problem.

Problem5:

 Headlight not working

possible cause:

1. Bulb burnt out.

2. Loose electrical wires.

possible solution :

1. Replace bulb

To change a bulb:

  • Make certain the vacuum has been switched off and unplugged earlier than changing the light bulb.
  • permit the light bulb to chill. Remove the two screws and take away the light cover.
  • Remove the burned-out mild bulb and pull it from the socket.
  • Insert a new bulb.
  • Attach the light cover using each screws.

2. replace wires

Problem6:

 Brushroll not rotating

possible cause:

1. Brushes clogged.

2. Brushroll switch in OFF place.

3. Brushroll must be reset.

possible solution :

1. Unplug the unit.

Remove particles from brush roll.

2. Slide brush roll ON/OFF switch to the ON place to activate brushes

  • Bring the vacuum cleaner into its vertical locking place.

NOTE: Switch brush rolls off when utilizing the hos.

  • Press the discharge button to release the cleaning wand. The cleaning wand with the built-in brush can be utilized for cleaning surfaces.
  • While urgent the hose release button, pull out the suction hose to release it from the cleaning wand.
  • Straighten the hose and hook the hose clip into the fastening ring to prevent the upright vacuum cleaner from toppling over throughout use.

3. Press the brush roll reset button.

Problem7:

 Dirt container won’t lock in place

possible cause:

1. Dirt container lid just isn’t aligned correctly.

2. Alignment tab not aligned.

possible solution :

1. Remove and realign lid.

2. Realign tab.

Read also:

After reading and following the problems and possible causes and possible solutions you may know now how to fix a dirt devil vacuum cleaner.